CPack RPM Generator

The built in (binary) CPack RPM generator (Unix only)

Variables specific to CPack RPM generator

The CPack RPM generator may be used to create RPM packages using CPack. The CPack RPM generator is a CPack generator thus it uses the CPACK_XXX variables used by CPack.

The CPack RPM generator has specific features which are controlled by the specifics CPACK_RPM_XXX variables.

CPACK_RPM_<COMPONENT>_XXXX variables may be used in order to have component-specific values. Note however that <COMPONENT> refers to the grouping name written in upper case. It may be either a component name or a component GROUP name. Usually, those variables correspond to RPM spec file entities. One may find information about spec files here https://rpm.org/documentation.

Changed in version 3.6: <COMPONENT> part of variables is preferred to be in upper case (e.g. if component is named foo then use CPACK_RPM_FOO_XXXX variable name format) as is with other CPACK_<COMPONENT>_XXXX variables. For the purposes of back compatibility (CMake/CPack version 3.5 and lower) support for same cased component (e.g. fOo would be used as CPACK_RPM_fOo_XXXX) is still supported for variables defined in older versions of CMake/CPack but is not guaranteed for variables that will be added in the future. For the sake of back compatibility same cased component variables also override upper cased versions where both are present.

Here are some CPack RPM generator wiki resources that are here for historic reasons and are no longer maintained but may still prove useful:

• https://gitlab.kitware.com/cmake/community/-/wikis/doc/cpack/Configuration

• https://gitlab.kitware.com/cmake/community/-/wikis/doc/cpack/PackageGenerators#rpm-unix-only

List of CPack RPM generator specific variables:

CPACK_RPM_COMPONENT_INSTALL

Enable component packaging for CPack RPM generator

Mandatory:

No

Default:

OFF

If enabled (ON) multiple packages are generated. By default a single package containing files of all components is generated.

CPACK_RPM_PACKAGE_SUMMARY

CPACK_RPM_<component>_PACKAGE_SUMMARY

The RPM package summary.

Mandatory:

Yes

Default:

CPACK_PACKAGE_DESCRIPTION_SUMMARY

New in version 3.2: Per-component CPACK_RPM_<component>_PACKAGE_SUMMARY variables.

CPACK_RPM_PACKAGE_NAME

CPACK_RPM_<component>_PACKAGE_NAME

The RPM package name.

Mandatory:

Yes

Default:

CPACK_PACKAGE_NAME

New in version 3.5: Per-component CPACK_RPM_<component>_PACKAGE_NAME variables.

CPACK_RPM_FILE_NAME

CPACK_RPM_<component>_FILE_NAME

New in version 3.6.

Package file name.

Mandatory:

Yes

Default:

<CPACK_PACKAGE_FILE_NAME>[-<component>].rpm with spaces replaced by '-'

This may be set to:

RPM-DEFAULT

Tell rpmbuild to automatically generate the package file name.

<file-name>[.rpm]

Use the given file name.

Changed in version 3.29: The .rpm suffix will be automatically added if missing. Previously the suffix was required.

Note

By using user provided spec file, rpm macro extensions such as for generating debuginfo packages or by simply using multiple components more than one rpm file may be generated, either from a single spec file or from multiple spec files (each component execution produces its own spec file). In such cases duplicate file names may occur as a result of this variable setting or spec file content structure. Duplicate files get overwritten and it is up to the packager to set the variables in a manner that will prevent such errors.

CPACK_RPM_MAIN_COMPONENT

New in version 3.8.

Main component that is packaged without component suffix.

Mandatory:

No

Default:

This variable can be set to any component or group name so that component or group rpm package is generated without component suffix in filename and package name.

CPACK_RPM_PACKAGE_EPOCH

New in version 3.10.

The RPM package epoch

Mandatory:

No

Default:

Optional number that should be incremented when changing versioning schemas or fixing mistakes in the version numbers of older packages.

CPACK_RPM_PACKAGE_VERSION

The RPM package version.

Mandatory:

Yes

Default:

CPACK_PACKAGE_VERSION

CPACK_RPM_PACKAGE_ARCHITECTURE

CPACK_RPM_<component>_PACKAGE_ARCHITECTURE

The RPM package architecture.

Mandatory:

Yes

Default:

Native architecture output by uname -m

This may be set to noarch if you know you are building a noarch package.

New in version 3.3: Per-component CPACK_RPM_<component>_PACKAGE_ARCHITECTURE variables.

CPACK_RPM_PACKAGE_RELEASE

The RPM package release.

Mandatory:

Yes

Default:

1

This is the numbering of the RPM package itself, i.e. the version of the packaging and not the version of the content (see CPACK_RPM_PACKAGE_VERSION). One may change the default value if the previous packaging was buggy and/or you want to put here a fancy Linux distro specific numbering.

Note

This is the string that goes into the RPM Release: field. Some distros (e.g. Fedora, CentOS) require 1%{?dist} format and not just a number. %{?dist} part can be added by setting CPACK_RPM_PACKAGE_RELEASE_DIST.

CPACK_RPM_PACKAGE_RELEASE_DIST

New in version 3.6.

The dist tag that is added RPM Release: field.

Mandatory:

No

Default:

OFF

This is the reported %{dist} tag from the current distribution or empty %{dist} if RPM macro is not set. If this variable is set then RPM Release: field value is set to ${CPACK_RPM_PACKAGE_RELEASE}%{?dist}.

CPACK_RPM_PACKAGE_LICENSE

The RPM package license policy.

Mandatory:

Yes

Default:

"unknown"

CPACK_RPM_PACKAGE_GROUP

CPACK_RPM_<component>_PACKAGE_GROUP

The RPM package group.

Mandatory:

Yes

Default:

"unknown"

New in version 3.5: Per-component CPACK_RPM_<component>_PACKAGE_GROUP variables.

CPACK_RPM_PACKAGE_VENDOR

The RPM package vendor.

Mandatory:

Yes

Default:

CPACK_PACKAGE_VENDOR if set or "unknown"

CPACK_RPM_PACKAGE_URL

CPACK_RPM_<component>_PACKAGE_URL

The projects URL.

Mandatory:

No

Default:

CMAKE_PROJECT_HOMEPAGE_URL

New in version 3.12: The CMAKE_PROJECT_HOMEPAGE_URL variable.

CPACK_RPM_PACKAGE_DESCRIPTION

CPACK_RPM_<component>_PACKAGE_DESCRIPTION

RPM package description.

Mandatory:

Yes

Default:

• CPACK_COMPONENT_<compName>_DESCRIPTION (component based installers only) if set,

• CPACK_PACKAGE_DESCRIPTION_FILE if set, or

• no package description available

New in version 3.2: Per-component CPACK_RPM_<component>_PACKAGE_DESCRIPTION variables.

CPACK_RPM_COMPRESSION_TYPE

RPM compression type.

Mandatory:

No

Default:

(system default)

May be used to override RPM compression type to be used to build the RPM. For example some Linux distributions default to xz or zstd. Using this, one can specify a specific compression type to be used.

Possible values are:

lzma

Lempel–Ziv–Markov chain algorithm

xz

XZ Utils compression

bzip2

bzip2 Burrows–Wheeler algorithm

gzip

GNU Gzip compression

zstd

New in version 3.31.

Zstandard compression

CPACK_RPM_PACKAGE_AUTOREQ

CPACK_RPM_<component>_PACKAGE_AUTOREQ

RPM spec autoreq field.

Mandatory:

No

Default:

May be used to enable (1, yes) or disable (0, no) automatic shared libraries dependency detection. Dependencies are added to requires list.

Note

By default automatic dependency detection is enabled by rpm generator.

CPACK_RPM_PACKAGE_AUTOPROV

CPACK_RPM_<component>_PACKAGE_AUTOPROV

RPM spec autoprov field.

Mandatory:

No

Default:

May be used to enable (1, yes) or disable (0, no) automatic listing of shared libraries that are provided by the package. Shared libraries are added to provides list.

Note

By default automatic provides detection is enabled by rpm generator.

CPACK_RPM_PACKAGE_AUTOREQPROV

CPACK_RPM_<component>_PACKAGE_AUTOREQPROV

RPM spec autoreqprov field.

Mandatory:

No

Default:

Variable enables/disables autoreq and autoprov at the same time. See CPACK_RPM_PACKAGE_AUTOREQ and CPACK_RPM_PACKAGE_AUTOPROV for more details.

Note

By default automatic detection feature is enabled by rpm.

CPACK_RPM_PACKAGE_REQUIRES

CPACK_RPM_<component>_PACKAGE_REQUIRES

RPM spec requires field.

Mandatory:

No

Default:

May be used to set RPM dependencies (requires). Note that you must enclose the complete requires string between quotes, for example:

set(CPACK_RPM_PACKAGE_REQUIRES "python >= 2.5.0, cmake >= 2.8")

The required package list of an RPM file could be printed with:

rpm -qp --requires file.rpm

CPACK_RPM_PACKAGE_CONFLICTS

CPACK_RPM_<component>_PACKAGE_CONFLICTS

RPM spec conflicts field.

Mandatory:

No

Default:

May be used to set negative RPM dependencies (conflicts). Note that you must enclose the complete requires string between quotes, for example:

set(CPACK_RPM_PACKAGE_CONFLICTS "libxml2")

The conflicting package list of an RPM file could be printed with:

rpm -qp --conflicts file.rpm

CPACK_RPM_PACKAGE_REQUIRES_PRE

CPACK_RPM_<component>_PACKAGE_REQUIRES_PRE

New in version 3.2.

RPM spec requires(pre) field.

Mandatory:

No

Default:

May be used to set RPM preinstall dependencies (requires(pre)). Note that you must enclose the complete requires string between quotes, for example:

set(CPACK_RPM_PACKAGE_REQUIRES_PRE "shadow-utils, initscripts")

CPACK_RPM_PACKAGE_REQUIRES_POST

CPACK_RPM_<component>_PACKAGE_REQUIRES_POST

New in version 3.2.

RPM spec requires(post) field.

Mandatory:

No

Default:

May be used to set RPM postinstall dependencies (requires(post)). Note that you must enclose the complete requires string between quotes, for example:

set(CPACK_RPM_PACKAGE_REQUIRES_POST "shadow-utils, initscripts")

CPACK_RPM_PACKAGE_REQUIRES_POSTUN

CPACK_RPM_<component>_PACKAGE_REQUIRES_POSTUN

New in version 3.2.

RPM spec requires(postun) field.

Mandatory:

No

Default:

May be used to set RPM postuninstall dependencies (requires(postun)). Note that you must enclose the complete requires string between quotes, for example:

set(CPACK_RPM_PACKAGE_REQUIRES_POSTUN "shadow-utils, initscripts")

CPACK_RPM_PACKAGE_REQUIRES_PREUN

CPACK_RPM_<component>_PACKAGE_REQUIRES_PREUN

New in version 3.2.

RPM spec requires(preun) field.

Mandatory:

No

Default:

May be used to set RPM preuninstall dependencies (requires(preun)). Note that you must enclose the complete requires string between quotes, for example:

set(CPACK_RPM_PACKAGE_REQUIRES_PREUN "shadow-utils, initscripts")

CPACK_RPM_PACKAGE_SUGGESTS

CPACK_RPM_<component>_PACKAGE_SUGGESTS

RPM spec suggest field.

Mandatory:

No

Default:

May be used to set weak RPM dependencies (suggests). If rpmbuild doesn't support the Suggests tag, CPack will emit a warning and ignore this variable. Note that you must enclose the complete requires string between quotes.

CPACK_RPM_PACKAGE_PROVIDES

CPACK_RPM_<component>_PACKAGE_PROVIDES

RPM spec provides field.

Mandatory:

No

Default:

May be used to set RPM dependencies (provides). The provided package list of an RPM file could be printed with:

rpm -qp --provides file.rpm

CPACK_RPM_PACKAGE_OBSOLETES

CPACK_RPM_<component>_PACKAGE_OBSOLETES

RPM spec obsoletes field.

Mandatory:

No

Default:

May be used to set RPM packages that are obsoleted by this one.

CPACK_RPM_PACKAGE_RELOCATABLE

build a relocatable RPM.

Mandatory:

No

Default:

CPACK_PACKAGE_RELOCATABLE

If this variable is set to TRUE or ON, the CPack RPM generator will try to build a relocatable RPM package. A relocatable RPM may be installed using:

rpm --prefix or --relocate

in order to install it at an alternate place see rpm(8). Note that currently this may fail if CPACK_SET_DESTDIR is set to ON. If CPACK_SET_DESTDIR is set then you will get a warning message but if there is file installed with absolute path you'll get unexpected behavior.

CPACK_RPM_SPEC_INSTALL_POST

Deprecated since version 2.8.12: Use CPACK_RPM_SPEC_MORE_DEFINE instead.

Mandatory:

No

Default:

May be used to override the __spec_install_post section within the generated spec file. This affects the install step during package creation, not during package installation. For adding operations to be performed during package installation, use CPACK_RPM_POST_INSTALL_SCRIPT_FILE instead.

CPACK_RPM_SPEC_MORE_DEFINE

RPM extended spec definitions lines.

Mandatory:

No

Default:

May be used to add any %define lines to the generated spec file. An example of its use is to prevent stripping of executables (but note that this may also disable other default post install processing):

set(CPACK_RPM_SPEC_MORE_DEFINE "%define __spec_install_post /bin/true")

CPACK_RPM_PACKAGE_DEBUG

Toggle CPack RPM generator debug output.

Mandatory:

No

Default:

May be set when invoking cpack in order to trace debug information during CPack RPM run. For example you may launch CPack like this:

cpack -D CPACK_RPM_PACKAGE_DEBUG=1 -G RPM

CPACK_RPM_USER_BINARY_SPECFILE

CPACK_RPM_<componentName>_USER_BINARY_SPECFILE

A user provided spec file.

Mandatory:

No

Default:

May be set by the user in order to specify a USER binary spec file to be used by the CPack RPM generator instead of generating the file. The specified file will be processed by configure_file( @ONLY).

CPACK_RPM_GENERATE_USER_BINARY_SPECFILE_TEMPLATE

Spec file template.

Mandatory:

No

Default:

If set CPack will generate a template for USER specified binary spec file and stop with an error. For example launch CPack like this:

cpack -D CPACK_RPM_GENERATE_USER_BINARY_SPECFILE_TEMPLATE=1 -G RPM

The user may then use this file in order to hand-craft is own binary spec file which may be used with CPACK_RPM_USER_BINARY_SPECFILE.

CPACK_RPM_PRE_INSTALL_SCRIPT_FILE

CPACK_RPM_PRE_UNINSTALL_SCRIPT_FILE

CPACK_RPM_PRE_TRANS_SCRIPT_FILE

Path to file containing pre install/uninstall/transaction script.

Mandatory:

No

Default:

May be used to embed a pre installation/uninstallation/transaction script in the spec file. The referred script file (or both) will be read and directly put after the %pre or %preun section If CPACK_RPM_COMPONENT_INSTALL is set to ON the install/uninstall/transaction script for each component can be overridden with CPACK_RPM_<COMPONENT>_PRE_INSTALL_SCRIPT_FILE, CPACK_RPM_<COMPONENT>_PRE_UNINSTALL_SCRIPT_FILE, and CPACK_RPM_<COMPONENT>_PRE_TRANS_SCRIPT_FILE One may verify which scriptlet has been included with:

rpm -qp --scripts  package.rpm

New in version 3.18: The CPACK_RPM_PRE_TRANS_SCRIPT_FILE variable.

CPACK_RPM_POST_INSTALL_SCRIPT_FILE

CPACK_RPM_POST_UNINSTALL_SCRIPT_FILE

CPACK_RPM_POST_TRANS_SCRIPT_FILE

Path to file containing post install/uninstall/transaction script.

Mandatory:

No

Default:

May be used to embed a post installation/uninstallation/transaction script in the spec file. The referred script file (or both) will be read and directly put after the %post or %postun section. If CPACK_RPM_COMPONENT_INSTALL is set to ON the install/uninstall/transaction script for each component can be overridden with CPACK_RPM_<COMPONENT>_POST_INSTALL_SCRIPT_FILE, CPACK_RPM_<COMPONENT>_POST_UNINSTALL_SCRIPT_FILE, and CPACK_RPM_<COMPONENT>_POST_TRANS_SCRIPT_FILE One may verify which scriptlet has been included with:

rpm -qp --scripts  package.rpm

New in version 3.18: The CPACK_RPM_POST_TRANS_SCRIPT_FILE variable.

CPACK_RPM_USER_FILELIST

CPACK_RPM_<COMPONENT>_USER_FILELIST

Mandatory:

No

Default:

May be used to explicitly specify %(<directive>) file line in the spec file. Like %config(noreplace) or any other directive that be found in the %files section. Since the CPack RPM generator is generating the list of files (and directories) the user specified files of the CPACK_RPM_<COMPONENT>_USER_FILELIST list will be removed from the generated list. If referring to directories do not add a trailing slash.

New in version 3.8: You can have multiple directives per line, as in %attr(600,root,root) %config(noreplace).

CPACK_RPM_CHANGELOG_FILE

RPM changelog file.

Mandatory:

No

Default:

May be used to embed a changelog in the spec file. The referred file will be read and directly put after the %changelog section.

CPACK_RPM_EXCLUDE_FROM_AUTO_FILELIST

list of path to be excluded.

Mandatory:

No

Default:

The following paths are excluded by default:

• /etc

• /etc/init.d

• /usr

• /usr/bin

• /usr/include

• /usr/lib

• /usr/libx32

• /usr/lib64

• /usr/share

• /usr/share/aclocal

• /usr/share/doc

May be used to exclude path (directories or files) from the auto-generated list of paths discovered by CPack RPM. The default value contains a reasonable set of values if the variable is not defined by the user. If the variable is defined by the user then the CPack RPM generator will NOT any of the default path. If you want to add some path to the default list then you can use CPACK_RPM_EXCLUDE_FROM_AUTO_FILELIST_ADDITION variable.

New in version 3.10: Added /usr/share/aclocal to the default list of excludes.

CPACK_RPM_EXCLUDE_FROM_AUTO_FILELIST_ADDITION

additional list of path to be excluded.

Mandatory:

No

Default:

May be used to add more exclude path (directories or files) from the initial default list of excluded paths. See CPACK_RPM_EXCLUDE_FROM_AUTO_FILELIST.

CPACK_RPM_RELOCATION_PATHS

New in version 3.2.

Packages relocation paths list.

Mandatory:

No

Default:

May be used to specify more than one relocation path per relocatable RPM. Variable contains a list of relocation paths that if relative are prefixed by the value of CPACK_RPM_<COMPONENT>_PACKAGE_PREFIX or by the value of CPACK_PACKAGING_INSTALL_PREFIX if the component version is not provided. Variable is not component based as its content can be used to set a different path prefix for e.g. binary dir and documentation dir at the same time. Only prefixes that are required by a certain component are added to that component - component must contain at least one file/directory/symbolic link with CPACK_RPM_RELOCATION_PATHS prefix for a certain relocation path to be added. Package will not contain any relocation paths if there are no files/directories/symbolic links on any of the provided prefix locations. Packages that either do not contain any relocation paths or contain files/directories/symbolic links that are outside relocation paths print out an AUTHOR_WARNING that RPM will be partially relocatable.

CPACK_RPM_<COMPONENT>_PACKAGE_PREFIX

New in version 3.2.

Per component relocation path install prefix.

Mandatory:

No

Default:

CPACK_PACKAGING_INSTALL_PREFIX

May be used to set per component CPACK_PACKAGING_INSTALL_PREFIX for relocatable RPM packages.

CPACK_RPM_NO_INSTALL_PREFIX_RELOCATION

CPACK_RPM_NO_<COMPONENT>_INSTALL_PREFIX_RELOCATION

New in version 3.3.

Removal of default install prefix from relocation paths list.

Mandatory:

No

Default:

CPACK_PACKAGING_INSTALL_PREFIX or CPACK_RPM_<COMPONENT>_PACKAGE_PREFIX are treated as one of relocation paths

May be used to remove CPACK_PACKAGING_INSTALL_PREFIX and CPACK_RPM_<COMPONENT>_PACKAGE_PREFIX from relocatable RPM prefix paths.

CPACK_RPM_ADDITIONAL_MAN_DIRS

New in version 3.3.

Mandatory:

No

Default:

Regular expressions that are added by default were taken from brp-compress RPM macro:

• /usr/man/man.*

• /usr/man/.*/man.*

• /usr/info.*

• /usr/share/man/man.*

• /usr/share/man/.*/man.*

• /usr/share/info.*

• /usr/kerberos/man.*

• /usr/X11R6/man/man.*

• /usr/lib/perl5/man/man.*

• /usr/share/doc/.*/man/man.*

• /usr/lib/.*/man/man.*

May be used to set additional man dirs that could potentially be compressed by brp-compress RPM macro. Variable content must be a list of regular expressions that point to directories containing man files or to man files directly. Note that in order to compress man pages a path must also be present in brp-compress RPM script and that brp-compress script must be added to RPM configuration by the operating system.

CPACK_RPM_DEFAULT_USER

CPACK_RPM_<compName>_DEFAULT_USER

New in version 3.6.

default user ownership of RPM content

Mandatory:

No

Default:

root

Value should be user name and not UID. Note that <compName> must be in upper-case.

CPACK_RPM_DEFAULT_GROUP

CPACK_RPM_<compName>_DEFAULT_GROUP

New in version 3.6.

default group ownership of RPM content

Mandatory:

No

Default:

root

Value should be group name and not GID. Note that <compName> must be in upper-case.

CPACK_RPM_DEFAULT_FILE_PERMISSIONS

CPACK_RPM_<compName>_DEFAULT_FILE_PERMISSIONS

New in version 3.6.

default permissions used for packaged files

Mandatory:

No

Default:

(system default)

Accepted values are lists with PERMISSIONS. Valid permissions are:

• OWNER_READ

• OWNER_WRITE

• OWNER_EXECUTE

• GROUP_READ

• GROUP_WRITE

• GROUP_EXECUTE

• WORLD_READ

• WORLD_WRITE

• WORLD_EXECUTE

Note that <compName> must be in upper-case.

CPACK_RPM_DEFAULT_DIR_PERMISSIONS

CPACK_RPM_<compName>_DEFAULT_DIR_PERMISSIONS

New in version 3.6.

default permissions used for packaged directories

Mandatory:

No

Default:

(system default)

Accepted values are lists with PERMISSIONS. Valid permissions are the same as for CPACK_RPM_DEFAULT_FILE_PERMISSIONS. Note that <compName> must be in upper-case.

CPACK_RPM_INSTALL_WITH_EXEC

New in version 3.11.

force execute permissions on programs and shared libraries

Mandatory:

No

Default:

(system default)

Force set owner, group and world execute permissions on programs and shared libraries. This can be used for creating valid rpm packages on systems such as Debian where shared libraries do not have execute permissions set.

Note

Programs and shared libraries without execute permissions are ignored during separation of debug symbols from the binary for debuginfo packages.

Packaging of Symbolic Links

New in version 3.3.

The CPack RPM generator supports packaging of symbolic links:

execute_process(COMMAND ${CMAKE_COMMAND}
  -E create_symlink <relative_path_location> <symlink_name>)
install(FILES ${CMAKE_CURRENT_BINARY_DIR}/<symlink_name>
  DESTINATION <symlink_location> COMPONENT libraries)

Symbolic links will be optimized (paths will be shortened if possible) before being added to the package or if multiple relocation paths are detected, a post install symlink relocation script will be generated.

Symbolic links may point to locations that are not packaged by the same package (either a different component or even not packaged at all) but those locations will be treated as if they were a part of the package while determining if symlink should be either created or present in a post install script - depending on relocation paths.

Changed in version 3.6: Symbolic links that point to locations outside packaging path produce a warning and are treated as non relocatable permanent symbolic links. Previous versions of CMake produced an error in this case.

Currently there are a few limitations though:

• For component based packaging component interdependency is not checked when processing symbolic links. Symbolic links pointing to content of a different component are treated the same way as if pointing to location that will not be packaged.

• Symbolic links pointing to a location through one or more intermediate symbolic links will not be handled differently - if the intermediate symbolic link(s) is also on a relocatable path, relocating it during package installation may cause initial symbolic link to point to an invalid location.

Packaging of debug information

New in version 3.7.

Debuginfo packages contain debug symbols and sources for debugging packaged binaries.

Debuginfo RPM packaging has its own set of variables:

CPACK_RPM_DEBUGINFO_PACKAGE

CPACK_RPM_<component>_DEBUGINFO_PACKAGE

Enable generation of debuginfo RPM package(s).

Mandatory:

No

Default:

OFF

Note

Binaries must contain debug symbols before packaging so use either Debug or RelWithDebInfo for CMAKE_BUILD_TYPE variable value.

Additionally, if CPACK_STRIP_FILES is set, the files will be stripped before they get to the RPM generator, so will not contain debug symbols and a debuginfo package will not get built. Do not use with CPACK_STRIP_FILES.

Note

Packages generated from packages without binary files, with binary files but without execute permissions or without debug symbols will cause packaging termination.

CPACK_BUILD_SOURCE_DIRS

Provides locations of root directories of source files from which binaries were built.

Mandatory:

Yes if CPACK_RPM_DEBUGINFO_PACKAGE is set

Default:

Note

For CMake project CPACK_BUILD_SOURCE_DIRS is set by default to point to CMAKE_SOURCE_DIR and CMAKE_BINARY_DIR paths.

Note

Sources with path prefixes that do not fall under any location provided with CPACK_BUILD_SOURCE_DIRS will not be present in debuginfo package.

CPACK_RPM_BUILD_SOURCE_DIRS_PREFIX

CPACK_RPM_<component>_BUILD_SOURCE_DIRS_PREFIX

Prefix of location where sources will be placed during package installation.

Mandatory:

Yes if CPACK_RPM_DEBUGINFO_PACKAGE is set

Default:

/usr/src/debug/${CPACK_PACKAGE_FILE_NAME} and for component packaging /usr/src/debug/${CPACK_PACKAGE_FILE_NAME}-<component>

Note

Each source path prefix is additionally suffixed by src_<index> where index is index of the path used from CPACK_BUILD_SOURCE_DIRS variable. This produces ${CPACK_RPM_BUILD_SOURCE_DIRS_PREFIX}/src_<index> replacement path. Limitation is that replaced path part must be shorter or of equal length than the length of its replacement. If that is not the case either CPACK_RPM_BUILD_SOURCE_DIRS_PREFIX variable has to be set to a shorter path or source directories must be placed on a longer path.

CPACK_RPM_DEBUGINFO_EXCLUDE_DIRS

Directories containing sources that should be excluded from debuginfo packages.

Mandatory:

No

Default:

The following paths are excluded by default:

• /usr

• /usr/src

• /usr/src/debug

Listed paths are owned by other RPM packages and should therefore not be deleted on debuginfo package uninstallation.

CPACK_RPM_DEBUGINFO_EXCLUDE_DIRS_ADDITION

Paths that should be appended to CPACK_RPM_DEBUGINFO_EXCLUDE_DIRS for exclusion.

Mandatory:

No

Default:

CPACK_RPM_DEBUGINFO_SINGLE_PACKAGE

New in version 3.8.

Create a single debuginfo package even if components packaging is set.

Mandatory:

No

Default:

OFF

When this variable is enabled it produces a single debuginfo package even if component packaging is enabled.

When using this feature in combination with components packaging and there is more than one component this variable requires CPACK_RPM_MAIN_COMPONENT to be set.

Note

If none of the CPACK_RPM_<component>_DEBUGINFO_PACKAGE variables is set then CPACK_RPM_DEBUGINFO_PACKAGE is automatically set to ON when CPACK_RPM_DEBUGINFO_SINGLE_PACKAGE is set.

CPACK_RPM_DEBUGINFO_FILE_NAME

CPACK_RPM_<component>_DEBUGINFO_FILE_NAME

New in version 3.9.

Debuginfo package file name.

Mandatory:

No

Default:

rpmbuild tool generated package file name

Alternatively provided debuginfo package file name must end with .rpm suffix and should differ from file names of other generated packages.

Variable may contain @cpack_component@ placeholder which will be replaced by component name if component packaging is enabled otherwise it deletes the placeholder.

Setting the variable to RPM-DEFAULT may be used to explicitly set filename generation to default.

Note

CPACK_RPM_FILE_NAME also supports rpmbuild tool generated package file name - disabled by default but can be enabled by setting the variable to RPM-DEFAULT.

Packaging of sources (SRPM)

New in version 3.7.

SRPM packaging is enabled by setting CPACK_RPM_PACKAGE_SOURCES variable while usually using CPACK_INSTALLED_DIRECTORIES variable to provide directory containing CMakeLists.txt and source files.

For CMake projects SRPM package would be produced by executing:

cpack -G RPM --config ./CPackSourceConfig.cmake

Note

Produced SRPM package is expected to be built with cmake(1) executable and packaged with cpack(1) executable so CMakeLists.txt has to be located in root source directory and must be able to generate binary rpm packages by executing cpack -G command. The two executables as well as rpmbuild must also be present when generating binary rpm packages from the produced SRPM package.

Once the SRPM package is generated it can be used to generate binary packages by creating a directory structure for rpm generation and executing rpmbuild tool:

mkdir -p build_dir/{BUILD,BUILDROOT,RPMS,SOURCES,SPECS,SRPMS}
rpmbuild --define "_topdir <path_to_build_dir>" --rebuild <SRPM_file_name>

Generated packages will be located in build_dir/RPMS directory or its sub directories.

Note

SRPM package internally uses CPack/RPM generator to generate binary packages so CMakeScripts.txt can decide during the SRPM to binary rpm generation step what content the package(s) should have as well as how they should be packaged (monolithic or components). CMake can decide this for e.g. by reading environment variables set by the package manager before starting the process of generating binary rpm packages. This way a single SRPM package can be used to produce different binary rpm packages on different platforms depending on the platform's packaging rules.

Source RPM packaging has its own set of variables:

CPACK_RPM_PACKAGE_SOURCES

Should the content be packaged as a source rpm (default is binary rpm).

Mandatory:

No

Default:

OFF

Note

For cmake projects CPACK_RPM_PACKAGE_SOURCES variable is set to OFF in CPackConfig.cmake and ON in CPackSourceConfig.cmake generated files.

CPACK_RPM_SOURCE_PKG_BUILD_PARAMS

Additional command-line parameters provided to cmake(1) executable.

Mandatory:

No

Default:

CPACK_RPM_SOURCE_PKG_PACKAGING_INSTALL_PREFIX

Packaging install prefix that would be provided in CPACK_PACKAGING_INSTALL_PREFIX variable for producing binary RPM packages.

Mandatory:

Yes

Default:

/

CPACK_RPM_BUILDREQUIRES

List of source rpm build dependencies.

Mandatory:

No

Default:

May be used to set source RPM build dependencies (BuildRequires). Note that you must enclose the complete build requirements string between quotes, for example:

set(CPACK_RPM_BUILDREQUIRES "python >= 2.5.0, cmake >= 2.8")

CPACK_RPM_REQUIRES_EXCLUDE_FROM

New in version 3.22.

Mandatory:

No

Default:

May be used to keep the dependency generator from scanning specific files or directories for dependencies. Note that you can use a regular expression that matches all of the directories or files, for example:

set(CPACK_RPM_REQUIRES_EXCLUDE_FROM "bin/libqsqloci.*\\.so.*")